Gana Fill X body set is made in Korea and approved by the KFDA. Gana Fill X body set contains 1560MG of poly-L-lactic acid and 40CC of Hyaluronic Acid.
Warning: Last items in stock!
Reconstitute with 18ml of sterile water for injections
One vial contains Injectable PLLA 1560mg
40CC of Hyaluronic Acid
Made in Korea
Gana Fill X contains poly-L-lactic acid, which is a biocompatible, biodegradable substance that is gradually and naturally absorbed by the body and commonly found in dissolvable stitches. Gana Fill injectable that helps gradually replace lost collagen — an underlying cause of facial aging — for results that can last more than two years.
As a poly-L-lactic acid (PLLA) collagen stimulator, Gana Fill is different from typical dermal fillers such as hyaluronic acid. Poly(L-lactide) is a biodegradable material with good bio-absorbability and bio-compatibility. After degradation in the body, PLLA products are excreted by metabolism and thus has no harmful side effects to the human body. It works with your body within the deep dermis, rather than topically, to help revitalize collagen production and help restore your skin’s inner structure and volume.1-3 As the PLLA microparticles are absorbed, they help stimulate collagen production. Rebuilt collagen strands begin gradually helping to restore facial volume4 and the look of fullness to wrinkles and folds.
INJECTABLE POLY-L-LACTIC ACID POWDER
1.Quicker dissolution time-under one hour
-If you have no time ,You can reconstitute water and shake well for 10minutes,
-if you use vortex mixer ,dissolution time will be under 60 seconds, shake 60seconds then just use it
3.Larger quantity.GANAFILL 520mg VS other PLLA fillers 150mg (GANAFILL X 1560mg)
4.Better contouring effect
-because GANAFILL has more PLLA
5.Less volume loss at first injection
-In a few days of sculptra injection. There will be no augmentation, You will see Initial volume loss, You have to wait 1-2months until
you see augmentation But GANAFILL has lower Volume loss
6.Low nodule formation- more water more dilution lower grnuloma
GANA FILL PROCEDURE
1.Reconstitute with 18ml of sterile water at least 1hours before injection.
2.If you use vortex mixer ,dissolution time will be under 60 seconds.
3.Use blunt needle larger than 21G.
4.For subcutaneous injection. For better performance inject deeper.
5.Use fan technique and avoid injecting too much in one area.
6.Do not use for forehead, lips, nose or areas near the eyes.
7.Use for face, breast and hip volume augmentation and acne scar recovery.
8.Effects can be seen 4 weeks after treatment up until 8 weeks after treatment. Volume augmentation lasts for 2 years.
9.Vigorous massaging is necessary around the area of treatment for 30 minutes every day for the first week
10.Two or three session is needed
1.Do not treatment prohibited area.(lip, nose, forehead)
2.Use distilled water only. (Do not use a saline solution or water.)
3.Don't inject at one spot too much , inject widely and deeply to avoid granuloma formation
4.Patient have to get second treatment.(Check progress)
Second generation of 6D Slim Point Lipodissolve...
This is for 40 pcs of Essorb Twin Mono Screw...
Glamour HARD Hyaluronic Acid Filler with free...
Everline Cannula under eyes PDO Thread | Under...
Glamour Soft Hyaluronic Acid Filler with...
Everline MONO PDO Thread Lift | Thread Lifting...
Product Name : PN CELL White Benefits :...
Essorb Slice PDO cog Cannula barbed thread...
Derma Shine Strong Topical Anesthetic Numbing...
Gana Fill is made in Korea and approved by the...